Tweet
will it be healthy to put the cells between glass and make a silicon.
thanks
thanks
-
-
Glass front & back, is very insulative, and the cells will run hot. Hot is ok, except hot cells produce less power, and weak cells will die sooner.Powerfab top of pole PV mount (2) | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
|| Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
|| VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A
solar: http://tinyurl.com/LMR-Solar
gen: http://tinyurl.com/LMR-Lister -
thanks mike
ıf I use the back side with paper - aliminium then glass is it ok ?
I want to find a cheap way to encapsulation.
what do you offer me ? a cheap silicon ?Comment
-
paper is BAD. roof top heat will degrade it, till it ignites, less time if a cell goes bad and lights it.Powerfab top of pole PV mount (2) | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
|| Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
|| VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A
solar: http://tinyurl.com/LMR-Solar
gen: http://tinyurl.com/LMR-ListerComment
-
another system
is it ok to capsulate the cells with a quality silicon( water proof )Comment
-
silicone is not totally waterproof. if it was everyone would be using it. as its cheap.
As mike said cells between glass will overheat them very quickly possibly even break the glass if good edge sealing.Comment
-
hi
so , there is two ways and they are expensive
1- eva
2- sygradComment
-
Powerfab top of pole PV mount (2) | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
|| Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
|| VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A
solar: http://tinyurl.com/LMR-Solar
gen: http://tinyurl.com/LMR-ListerComment
-
another way
two sided glass and the back side of glass is water cooling system is possible maybeComment
-
Putting the panels in space is possible too - and just about as practical[SIGPIC][/SIGPIC]Comment
-
hi
is it enought to put the panels to spaceComment
-
Here is my suggestion for laying out your cells and not needing to use ANY yucky and or expensive backing. (1) gather up all the cells (2)place in suitable container (3) transport them(4)at destination lay a suitably sized plastic sheet over the ground (5) interconnect all the cell wires (6) terminate at a junction all wires (7) run suitably sized cable from junction box on the moon to earth.(7) connect to controller(8) connect to batteries and inverter(9) connect to a fridge full of beer(10)enjoy cold beer
Comment
-
hi
I dont understand may be I can connect to the sun directly
Comment
-
is this possible ?
silicon elastomer and carbon polimer is used in this example .
how it seems to you
thanksComment
Comment